152-L Blades Lane
Glen Burnie, Maryland 21060
(410) 761-2800 (800) 422-1433
fax: (410) 761-2944
email: sales@amerhose.com

Products

Petroleum Hose

Dredge Hose and Pipe

Safety Supplies

Hydraulic Hose and Fittings

Industrial Hose and Fittings

Contact Us

About Us

Home


  ADVANTAGES OF POLYETHELENE PIPE
   
Pipe, fittings and valves provide total system solutions
Durability, long-term strength and integrity
Flexible and lightweight
Superior corrosion, chemical & abrasion resistance
Non-toxic; environmentally safe (interior and exterior)
Indent printed for easy long-term identifications
Ease of handling, shipping, and installation
Heat-fused, fully restrained, leakproof joints
Improved flow rates over non-HDPE piping
Cost advantages
Continuous coiled pipe available from ½” to 6” OD
Straight length pipe available from ½” to 54” diameter
Produced in both IPS and DIPS sizes

 

Water Discharge T253AA

150 PSI

APPLICATION
High pressure, 150 PSI lay flat type hose
for general construction and mine water discharge.
COVER
Black weather and ozone-resistant EPDM
rubber.
REINFOREMENT
High tensile textile cords.
TUBE
Black EPDM rubber.
TEMPERATURE RANGE
-22°F to 176°F
STANDARD LENGTH
100 feet: 1 ½” through 10”
50 feet: 6”, 8”, 10” & 12”
WORKING PRESSURE
150 PSI constant (10 Bar) EXCEPT 12”
(100 PSI) Please note: 12” ID Maximum
Working Pressure is 100 PSI and it is
available only in 50’ lengths.
BRANDING
ALFAGOMMA – ITALY – T253 BAR (150 PSI) GENERAL PURPOSE EPDM (in green letters) – 1” through 10”: Solid Green Stripe on 12” ID

COUPLING SUGGESTIONS
Cam and groove, pin lug, short shank couplings or combination nipples attached with single bolt, double bolt, wire or band type clamps.

Kuriyama offers a full line of quick-couplings, pin lug shank couplings and combination nipples. Refer to your individual coupling sheets for type and pricing.

 

SERIES NO. NOMINAL ID NOMINAL OD APPROX. WT.lbs./100 ft. MAX. REC.WP (PSI)
  (in.) (mm) (in.) (mm)    
             
T253AA150 1½ 38 1.81 46 36 150
T253AA200 2 51 2.32 59 50 150
T253AA250 2½ 63 2.80 71 60 150
T253AA300 3 76 3.31 84 86 150
T253AA400 4 102 4.33 110 120 150
T253AA600 6 152 6.38 162 199 150
T253AA662 6 5/8 7.01 178 216 150
T253AA800 8 203 8.46 215 298 150
T253AA1000 10 254 10.63 270 510 150
T253AA1200 12 305 12.56 319 580 100

 

Water Suction
T202AA

*150 PSI EPDM MULTI-PURPOSE WATER SUCTION HOSE
APPLICATION
Suction and delivery of non-corrosive liquids for irrigation, construction, fertilizers and lasso acid solutions.
COVER
Black weather and ozone-resistant EPDM rubber.
REINFORCEMENT
Spiraled high tensile textile cords and 4 highly flexible steel helix wires.
TUBE
Black EPDM rubber.
TEMPERATURE RANGE
-22°F to 176°F
STANDARD LENGTH
100 feet: 1” through 4”
20, 50 feet: 5” 20, 25 feet: 8”
20, 25, 50 feet: 6” 20 feet: 10”, 12”
BRANDING
ALFAGOMMA – ITALY – T202 10 BAR (150 PSI) GENERAL PURPOSE EPDM (in green letters) EXCEPT 12” has a solid green stripe
COUPLING SUGGESTIONS
Cam and groove, pin lug, short shank couplings or combination nipples attached with single bolt, double bolt, wire or band type clamps.

 

SERIES NO. NOMINAL ID NOMINAL OD APPROX. WT.lbs./100 ft. MAX. REC.WP (PSI) MIN. BEND RADIUS (in.)
  (in.) (mm) (in.) (mm)      
               
T202AA100 1 25 1.38 35 48 150 4
T202AA125 1 ¼ 32 1.65 42 57 150 5
T202AA150 1 ½ 38 1.89 48 65 150 6
T202AA200 2 51 2.40 61 86 150 8
T202AA250 2 ½ 63 2.95 75 125 150 10
T202AA300 3 76 3.46 88 150 150 12
T202AA350 3 ½ 90 4.02 102 180 150 14
T202AA400 4 102 4.49 114 198 150 16
T202AA500 5 127 5.55 141 312 150 25
T202AA600 6 152 6.54 166 400 150 30
T202AA800 8 203 8.70 221 761 150 40
T202AA1000 10 254 10.71 272 905 150 50
T202AA1200 12 305 12.80 325 1500 90 60

 

DREDGE

TITAN-KERN
TKW708

SAND SUCTION HOSE – 3/8” N/R TUBE
TKW709 SAND SUCTION HOSE – ½” N/R TUBE
TKW710 SAND SUCTION HOSE – ¾” N/R TUBE
   
DESCRIPTION: Sand suction hose designed for full vacuum applications in the dredging of harbors, river channels and sand pits.
TUBE: Abrasion resistant Natural Rubber.

REINFORCEMENT: Multiple plies of polyester fabric with helix wire embedded in rubber.

COVER: Abrasion resistant rubber.
NOTE: Specifications for TKW708 & TKW709 available upon request.

 

TKW48 FLOATING DREDGE HOSE
DESCRIPTION: For use from the dredge to the pump station or from the pump station to shore. Used in place of steel pipe for flexibility and better abrasion resistance.
TUBE: Black abrasion resistant Natural Rubber.
REINFORCEMENT: Multiple plies of polyester fabric with a spring steel helix wire.
COVER: Neoprene. (also available with a urethane coating).
FLOATATION: Closed cell polyurethane encased in a polyester cord fabric for protection
against the elements.
I.D. O.D. WEIGHTLB/FT
6” 8 9/16” 13.80
65/8” 9 3/16” 14.97
8” 10 ¾” 18.77
8 5/8” 11 ¼” 19.76
10” 13 1/16” 26.60
10 ¾” 13 13/16” 28.30
12” 15 1/16” 35.49
12 ¾” 15 ¾” 37.43
14” 17 3/16” 42.60
16” 19 ¼” 50.64

 

TITAN-EXACTA
EW708 SAND SUCTION HOSE – 3/8” NR TUBE

 

I.D. O.D. BEND RADIUS REIN- FORMENT WORKING PRESSURE PSI

WEIGHT LB/FT

VACUUM RATING
4” 5 ½” 24” 4 plies 200 5.90 Full
4 ½” 6” 27” 4 plies 200 6.50 Full
5” 6 ½” 30” 4 plies 200 7.40 Full
5 ½” 7” 33” 4 plies 175 8.10 Full
6” 7 5/8” 36” 4 plies 175 10.10 Full
6 5/8” 8 ¼” 41” 4 plies 150 11.00 Full
8” 9 ¾” 48” 4 plies 150 14.40 Full
8 5/8” 10 5/16” 54” 4 plies 150 16.20 Full
10” 12 1/8” 60” 4 plies 150 21.40 Full
10 ¾” 12 7/8” 65” 4 plies 150 24.90 Full
12” 14” 72” 6 plies 150 26.70 Full
12 ¾” 14 7/8” 77” 6 plies 150 31.60 Full
13 ¼” 15 5/16” 80” 6 plies 150 32.50 Full
14” 16 1/8” 84” 6 plies 150 34.50 Full
15” 17 1/8” 90” 6 plies 150 36.70 Full
16” 18 3/16” 96” 8 plies 150 43.00 Full
18” 20 ½” 102” 8 plies 150 55.00 Full

 

EW709 SAND SUCTION HOSE – ½” NR TUBE

 

I.D. O.D. BEND RADIUS REIN- FORMENT WORKING PRESSURE PSI

WEIGHT LB/FT

VACUUM RATING
4” 5 13/16” 26” 4 plies 200 6.90 Full
4 ½” 6 5/16” 29” 4 plies 200 7.60 Full
5” 6 13/16” 32” 4 plies 200 8.60 Full
5 ½” 7 5/16” 36” 4 plies 175 9.40 Full
6” 13/16” 38” 4 plies 175 11.50 Full
6 5/8” 8 ½” 43” 4 plies 150 12.50 Full
8” 9 29/32” 50” 4 plies 150 16.20 Full
8 5/8” 10 5/8” 56” 4 plies 150 18.20 Full
10” 2 5/16” 62” 4 plies 150 23.70 Full
10 ¾” 13” 67” 4 plies 150 27.30 Full
12” 14 5/16” 74” 6 plies 150 29.40 Full
12 ¾” 15 1/8” 79” 6 plies 150 34.50 Full
13 ¼” 15 5/8” 82” 6 plies 150 35.50 Full
14” 16 5/16” 86” 6 plies 150 37.60 Full
15” 17 5/16” 92” 6 plies 150 40.00 Full
16” 18 ½” 98” 8 plies 150 46.50 Full
18” 20 ½” 104” 8 plies 150 62.00 Full

DESCRIPTION: Rugged in-line flexible connector for dredging operations. Durable design provides excellent abrasion resistance and ozone protection.
TUBE: Black Natural Rubber.
REINFORCEMENT: High tensile synthetic cord with wore helix.
COVER: SBR.
ENDS: Recommended fittings are MOD BIRF’s, Rotaloks, and rubber lined nipples and flanges.

TITAN-KERN
TKS907 DREDGE SLEEVE – 3/8” N/R TUBE
TKS908 DREDGE SLEEVE – ½” N/R TUBE
TKS909 DREDGE SLEEVE – ¾” N/R TUBE

 

I.D. O.D. WORKING PRESSURE PSI WEIGHT LB/FT
4 ½” 6 7/16” 150 7.77
6 5/8” 8 9/16” 150 10.75
8” 10 1/8” 150 13.84
8 5/8” 10 ¾” 150 14.79
10” 12 ¼” 150 18.29
10 ¾” 13 1/16” 150 19.50
12 ¾” 15 1/16” 150 22.74
14” 16 7/16” 150 26.66
16” 18 7/16” 150 30.12

DESCRIPTION: For river and harbor dredging. Used as a flexible connector between pipes on pontoon lines conveying dredged material to barges or dumping sites.
TUBE: Abrasion resistant rubber.
REINFORCEMENT: Multiple plies of polyester fabric.
COVER: Abrasion resistant rubber.
NOTE: Available with pipe O.D. for entire length of hose or pipe I.D. with straight or enlarged ends.
Specifications for TKS907 & TKS908 available upon request.

 

TITAN-EXACTA
ES907 DREDGE SLEEVE – 3/8” BLK NATURAL TUBE

 

I.D. O.D. BEND RADIUS WORKING PRESSURE PSI WEIGHT LB/FT
4” 5 1/8” 2 plies 200 3.50
4 ½” 5 5/8” 2 plies 200 3.90
5” 6 1/8” 2 plies 150 4.30
6” 7 5/16” 4 plies 150 6.10
6 5/8” 7 7/8” 4 plies 150 7.00
8” 9 5/16” 4 plies 150 8.30
8 5/8” 10” 4 plies 150 8.90
10” 11 5/8” 6 plies 150 12.00
10 ¾” 12 3/8” 6 plies 150 12.70
12” 13 5/8” 6 plies 150 14.40
12 ¾” 14 3/8” 6 plies 150 16.00
13 ¼” 14 7/8” 6 plies 150 17.00
14” 15 5/8” 6 plies 150 18.50
16” 17 7/8” 8 plies 150 23.00
18" 19 7/8” 8 plies 150 26.00

 

ES908 DREDGE SLEEVE – ½” BLK NATURAL TUBE

 

I.D. O.D. BEND RADIUS WORKING PRESSURE PSI WEIGHT LB/FT
4” 5 3/8”


2 plies 200 4.40
4 ½” 5 13/16” 2 plies 200 4.90
5” 6 11/16” 2 plies 150 5.40
6” 7 5/8” 4 plies 150 7.40
6 5/8” 8 1/8” 4 plies 150 8.00
8” 9 5/8” 4 plies 150 9.90
8 5/8” 10 3/16” 4 plies 150 11.00
10” 11 13/16” 6 plies 150 14.00
10 ¾” 12 5/8” 6 plies 150 15.10
12” 13 13/16” 6 plies 150 16.80
12 ¾” 14 5/8” 6 plies 150 18.00
13 ¼” 15 1/8” 6 plies 150 19.00
14” 15 13/16” 6 plies 150 20.00
16” 18” 8 plies 150 26.00
18" 20” 8 plies 150 30.00

DESCRIPTION: Rugged abrasion resistant flexible connectors. Designed exclusively for in-line dredge discharge service. Heavy duty construction provides excellent working pressures. Specially formulated tube offers superior protection against cuts, scuffs, or abrasions.
TUBE: Black Natural Rubber.
REINFORCEMENT: Multiple plies of high tensile synthetic cord.
COVER: SBR.
NOTE: Thicker tubes and higher working pressures available upon request.
ENDS: Recommended fittings are MOD BIRF’s, Rotaloks, and Rubber Lined fittings.

END FITTINGS

B.I.N.F. – BUILT-IN NIPPLE FLANGE
The hose is built around the nipple and then vulcanized for maximum holding power. Available in threaded, flanged, or grooved end styles.
ROTA-LOK
End with either Full Floating Flanges or Split Ring Flanges. A superior design to the old style “Rolled Angle Ring” type Beaded End. Tube extends through the nipple and up face of stub end. Full flow unrestricted area.

 

B.I.R.F./DUCK & RUBBER
A superior design to the Duck & Rubber Flange. Hose tube extends through nipple and up face of flange, offering a full flow unrestricted transition area.
MODIFIED B.I.R.F.
A superior design to the Duck & Rubber Flange. Hose tube extends through nipple and up face of flange, offering a full flow unrestricted transition area.


TIXF150 150 # FIXED FLANGE

 

TIXF300 300# FIXED FLANGE

 

TIXFL150 150# FLOATING FLANGE


SWAGED ON FITTINGS
In addition to furnishing built-in nipples and flanges, Titan has the capability of furnishing swaged on fittings.
SERVICE: Recommended for all types of dock hoses.
SIZE RANGE: 3” thru 10” I.D.
DESCRIPTION: Made of tubular steel or stainless steel. One end consists of a stem (threaded or
plain) fer rule and threaded slip-on flange. Standard flanges are 150# ASA drilling, however, other drillings are available upon request.


RING LOCK FITTINGS

PRESS-ON STEEL TUBE END–GALVANIZED

No. 3010

 

SIZE WT.
3” – 14 ga. 1 ¾
4” – 14 ga. 2
4” – 12 ga. 2
5” – 14 ga. 2 ¾
6” – 14 ga. 4
6” – 12 ga. 4 ½
7” – 14 ga. 4 ¼
8” – 14 ga. 6 ½
8” – 12 ga. 7 ¼
10” – 12 ga. 10
12” – 12 ga. 11 ¾

 

WELD-ON STEEL END – BLACK

No. 3015

 

SIZE WT.
3” – 14 ga. 1 ¼
4” – 14 ga. 1 ¼
4” – 12 ga. 2
5” – 14 ga. 1 ¾
6” – 14 ga. 2
6” – 12 ga. 3
7” – 14 ga. 3 ¼
8” – 14 ga. 3 ¼
8” – 12 ga. 4 ½
10” – 12 ga. 5 ½
12” – 12 ga. 6 ½

 

PRESS-ON STEEL COUPLER – GALVANIZED

No. 3020 With gasket

 

SIZE WT.
3” – 14 ga. 1 ½
4” – 14 ga. 2 ¼
4” – 12 ga. 3
5” – 14 ga. 3
6” – 14 ga. 4 ½
6” – 12 ga. 5
7” – 14 ga. 6
8” – 14 ga. 6 1/6
8” – 12 ga. 7 ¾
10” – 12 ga. 11 ¼
12” – 12 ga. 13

ROUND BACK ALSO AVAILABLE

WELD-ON STEEL COUPLER – BLACK

No. 3025 With gasket


SIZE WT.
3” – 14 ga. 1
4” – 14 ga. 1 ½
4” – 12 ga. 1 ¾
5” – 14 ga. 2
6” – 14 ga. 2 ½
6” – 12 ga. 3
7” – 14 ga. 4
8” – 14 ga. 5
8” – 12 ga. 4 ½
10” – 12 ga. 6 ¼
12” – 12 ga. 7 ½


MALE HOSE ADAPTER – GALVANIZED

No. 3175

 

SIZE WT.
MALE END HOSE END  
3” X 3”  
4” X 4” 3
4” X 4 ½”  
6” X 6” - 12 ga. 5 ½
8” X 8” - 12 ga. 8 ¾
10” X 10” - 12 ga.  
12” X 12” - 12 ga.  


FEMALE HOSE ADAPTER – GALVANIZED

No. 3176 With gasket.

 

SIZE WT.
MALE END HOSE END  
3” X 3”  
4” X 4” 5
4” X 4 ½”  
6” X 6” - 12 ga. 7 ½
8” X 8” - 12 ga. 9 ¾
10” X 10” - 12 ga.  
12” X 12” - 12 ga.  

ROUND BACK ALSO AVAILABLE


GIMBEL HOSE

 

The Gimbel hose design has greater flexibility which allows a tighter bend radius while still being virtually kink and distortion resistant.

What is a Gimbel Hose?

  • Gimbel hose is a custom made hose using steel rings for reinforcement instead of a continuous wire.

Why use a Gimbel Hose?

  • Individual steel ring reinforcement allows extreme flexibility.
  • Gimbel hose design allows a 50% or more better bend radius than a conventional hose design.
  • Gimbel hose can be used in shorter lengths and still obtain a tight bend radius.
  • Gimbel ring construction allows large diameter hose to reach full vacuum.
  • Kink and distortion resistant.
  • Gimbel design is similar to an accordian and allows some inward flexing.
Size Range: Up to 36” inside diameter
Recommended End Fittings: Modified BIRF, Rubber Lined, Roto-lok, & Duck & Rubber.
Note: Recommended end fittings allow a full flow, unrestricted transition area.

 

EWC436 HOSE
16” Spiral Hose with 56” Tested Bed Radius

Titan’s Custom Made Hose designers have developed a proprietary modified double spiral wire, corrugated construction that offers the bend radius normally achieved through a Gimbel design.

An example of the superior flexibility is a 16” I.D. hose in a lightweight construction which can achieve a 56” bend radius (a 90° bend). This new design allows Titan to match or surpass other manufactures’ implied or stated bend radius. A Gimbel design is still recommended for abrasive applications with higher working pressures and applications requiring a tighter bend radius.

Design Characteristics:

  • Highly flexible.
  • Greater bend radius.
  • Lightweight.
  • Light to non-abrasive applications.
  • Working pressure under 100 psi.
  • Available in most compounds and tire cords.
  • Used primarily with soft cuff ends (based on applications).
  • More economically priced than a Gimbel construction.

Applications:

  • Light to non-abrasive applications that demand a tight bend radius.
  • Price sensitive buyer who does not want a Gimbel product.
  • Achieves 90° bend with flexibility that a steel elbow does not offer.
  • Limited space required for installation.
Size Range:
8” thru 18” I.D.

Bend Radius:

I.D. Minimum Bend Radius
8” 30”
10” 38”
12” 45”
14” 52”
16” 56”
18” 66”











AMERICAN HOSE & COUPLING OFFERS A COMPLETE RANGE OF HIGH QUALITY POLETHYLENE PIPING SYSTEM PRODUCTS. WE ARE KNOWN FOR SUPERIOR SERVICE AND A TEAM OF PEOPLE DEDICATED TO THE INDUSTRY AND TO THE CUSTOMERS WE SERVE.

POLETHYLENE PIPE IS LIGHTER THAN TRADITIONAL PIPING MATERIAL, AND THAT RESULTS IN SUBSTANTIAL SAVINGS FOR HANDLING AND FASTER, LESS COSTLT INSTALLATION.

POLETHYLENE PIPE IS PRODUCED IN STRAIGHT LENGTHS OR IN COILS. SINCE PE IS NOT A BRITTLE MATERIAL, IT CAN BE INSTALLED WITH BENDS AND OVER UNEVEN TERRAIN EASILY IN CONTINUOUS LENGTHS WITHOUT ADDITIONAL WELDS OR COUPLINGS.

POLETHYLENE PIPE AND FITTINGS ARE WELL SUITED FOR USE IN SLURRY APPLICATIONS WHERE ITS INHERENT TOUGHNESS AND ABRASION RESISTANCE CAN BE FULLY UTILIZED. PE PIPE IS VERY RESILENT AND RESISTANT TO DAMAGE CAUSED BY EXTERNAL LOADS, VIBRATIONS, AND FROM PRESSURE SURGES SUCJ AS WATER HAMMER.

POLETHYLENE BUTT, SOCKET AND SIDEWALL FUSION CREATES A JOINING SYSTEM STRONGER THAN THE PIPE ITSELF MAKING A LEAKPROOF, FULLY RESISTRAINED JOINT.

SIGNIFICANT COST SAVINGS CAN BE REALIZED USING CSR POLYPIPE OVER TRADITIONAL MATERALS SUCH AS STEEL, DUCTILE IRON, FIBERGLASS, OR PVC, WITH THE SAME DESIGN PARAMETERS. REAL SAVINGS IN PRODUCT COSTS, INSTALLATION EFFICIENCY, AND LONG-LIFE EXPECTANCY ARE MAJOR ADVANTAGES OF POLYETHYLENE PIPE .

THE EXCEPTIONALLY SMOOTH INNER SURFACE OF POLETHYLENE PIPE OFFERS MINIMAL RESITANCE TO FLOW AND THE FLOW REMAINS RELATIVELY CONSTANT FOR THE LIFE OF THE PIPE, UNLIKE OTHER PIPING PRODUCTS THAT MUST ALLOW FOR A REDUCTION IN FLOW CAPACITY OVER TIME. WHEN USING POLETHYLENE PIPE, A HIGHER MAXIMUM FLOW RATE FOR A GIVEN SIZE CAN BE EXPECTED COMPARED TO OTHER TYPES OF PIPING MATERIALS.